What a circuit needs
Charge only flows when two things are present: a source that creates a voltage, such as a battery, and a closed loop of conducting material for the charge to travel round. Open the loop anywhere, with a switch or an empty lamp socket, and the flow stops everywhere at once.
The amount of flow is the current, measured in amperes (A). A current of one ampere means one coulomb of charge passing a point every second. By convention the current is drawn leaving the battery’s + terminal and returning to its − terminal, the way a positive charge would move. In metal wires the charges that actually move are electrons, which drift the opposite way; the convention dates from the time of Benjamin Franklin and has been kept ever since.
Ohm’s law: voltage, current and resistance
Voltage pushes the current; resistance holds it back. Ohm’s law ties the three together: the voltage across a part equals the current through it times its resistance, V = I × R. Rearranged, I = V ÷ R. It is named after the German physicist Georg Ohm, who published measurements of voltage and current in simple circuits in 1827.
In the room, four 1.5 V cells make a 6 V battery. Across a single 6 Ω lamp, the current is 6 ÷ 6 = 1 A. Double the resistance and the current halves; double the voltage and it doubles. A torch running on 3 V with a 60 Ω bulb draws 3 ÷ 60 = 0.05 A.
Series: one path for everything
In a series circuit the parts sit one after another on a single path, so every bit of charge passes through every lamp. The resistances simply add: three 6 Ω lamps behave like one 18 Ω lamp. More lamps means more total resistance and less current, which is why each lamp gets dimmer as you add another.
The current is the same everywhere in a series loop: an ammeter before the first lamp and one after the last read the same number. The battery’s voltage is shared out between the lamps, and the shares add up to the battery voltage. The lamp with the most resistance takes the biggest share. And because there is only one path, removing any lamp breaks it: all the others go out.
Parallel: a branch for each lamp
In a parallel circuit each lamp has its own branch, and every branch connects straight across the battery. So every lamp gets the full battery voltage, and each lamp’s current depends only on its own resistance: the branch with the least resistance carries the most current. The branch currents add up to the current leaving the battery.
Adding a branch gives the charge one more route, so the total resistance goes down, not up. Three 6 Ω lamps in parallel act like a single 2 Ω lamp, and on 6 V they draw 3 A from the battery instead of 1 A. Take one lamp out and the others stay lit, because their branches are still complete. Picture a kitchen whose appliances were all on one series path: the fridge would only run while the toaster, the dishwasher and the lights were on too. In parallel, each one works on its own.
Power: why a lamp glows brighter or dimmer
A lamp’s brightness follows the power it turns into light and heat, measured in watts (W). Power is voltage times current, P = V × I, and with Ohm’s law it can also be written P = I² × R or P = V² ÷ R. The room uses these to show how brightly each lamp glows.
The numbers explain the dimming. One 6 Ω lamp on 6 V takes 1 A and 6 W. Two of them in series share the voltage, carry 0.5 A and get only 1.5 W each, a quarter of the power. In parallel each one still has 6 V across it, still takes 1 A and still gets 6 W, but the battery now has to supply twice the current.
The room uses the simplifications of a first circuits lesson: the battery keeps its voltage whatever it supplies, the wires have no resistance and each lamp has a fixed resistance. The rules of series and parallel circuits hold for real parts too; only the exact numbers would differ a little.
Three common mistakes
“The lamps use up the current.” They do not. Charge is neither piled up nor used up in a circuit: in series the same current that enters the first lamp leaves the last one. What the lamps use is energy, which they take from the charge as it passes through them.
“More lamps always means more resistance.” Only in series. In parallel each new branch is an extra route, so the total resistance falls and the battery current rises.
“Electrons race from the battery to the lamp.” Electrons drift through a wire remarkably slowly, about a metre per hour. A lamp lights the moment the switch closes because the whole circuit, filament included, is already full of electrons, and they all start moving together.
Questions visitors ask
What is the difference between series and parallel circuits?
In series the parts are on one path: the same current goes through all of them and they share the battery voltage. In parallel each part has its own branch: each gets the full voltage and the branch currents add up. Remove one part in series and everything stops; in parallel the rest keeps working.
Why do lamps in series get dimmer when you add more?
Each lamp adds resistance to the single path, so the current falls for all of them. With less current and a smaller share of the voltage, each lamp gets less power. Two identical lamps in series each get a quarter of the power one lamp would get alone.
How can adding a resistor lower the total resistance?
When it is added in parallel. Each new branch is one more route for the charge, like opening an extra lane at a toll station: every car still passes one booth, but more cars get through each second. Three 6 Ω resistors in parallel act like a single 2 Ω resistor.
What does Ohm’s law say?
That the voltage across a part equals the current through it times its resistance: V = I × R. With 6 V across 6 Ω, the current is 1 A. Ohm’s law holds for metal wires and many other conductors over a wide range, but not for every device.
Is it safe to try this at home?
With a few torch cells and small bulbs, yes: that is how circuits are taught in school labs. Never experiment with the mains supply from wall sockets: it is dangerous.
Sources and further reading
- Ohm’s Law — The Physics Classroom
- Power: Putting Charges to Work — The Physics Classroom
- Two Types of Connections — The Physics Classroom
- Series Circuits — The Physics Classroom
- Parallel Circuits — The Physics Classroom
- Electric Current — The Physics Classroom
- Ohm’s law — Wikipedia
Cite this exhibit
Eurekarium. (2026). Circuits. https://eurekarium.com/electricity/circuits/
Last updated: